Tag Archives: pump runs dry

Prepping Your Metal Parts

Prepare your pump parts for an upgrade to DuPont™ Vespel CR-6100

Review on Pump Parts and upgrading to Vespel CR-6100

The National Geographic Channel used to run a show called Doomsday Preppers where survivalist families would prepare for apocalyptic disasters and societal collapse. Although that sounds like a lot of fun, at Boulden, we are more concerned with helping your pumps survive adverse process conditions with an upgrade to DuPont™ Vespel® CR-6100.

 

Last month, we outlined the measurements required for a Vespel® CR-6100 installation. When you have decided to go forward with the upgrade, the first step will be to prepare the metal parts to facilitate the installation.

 

Start with a Little Chamfer

Vespel® CR-6100 is used for stationary wear components–throttle bushings, case wear rings, center-stage bushings, inter-stage case rings, vertical pump shaft bearings, throat bushings, agitator bearings, API separator bearings-basically any product lubricated wear part.

 

The material is installed with a significant press fit. To facilitate the press fit operation, the metal bore into which you will be pressing the Vespel® CR-6100 requires a small chamfer or radius (Figure 1). It is very important that any corners or sharp edges are fully broken and smoothed with a stone so that the metal edge does not remove material from the outside surface of the Vespel® CR-6100 during the press operation.

Figure 1: Chamfer or Radius Leading Edge to facilitate press fit. (Note shoulder on low-pressure side.)

 

 

 

 

 

 

 

 

 

Make Sure There is a “Shoulder” or “Step”

For any part exposed to differential pressure, it is important that the design features a shoulder or step at the low-pressure end (shown on the right side of Figure 1) to ensure the differential pressure does not dislodge the Vespel® CR-6100 during operation.

 

Some radially split multi-stage pumps (BB4 and BB5) pumps feature metal wear rings welded into the pump diffusers with no step or shoulder incorporated in the design. In this case, you can consider modifying the diffusers so that the case wear rings have an “L” shaped profile like the rings below which were used in a hydrocracker charge pump.

Figure 2: “L” Shaped wear ring profile for BB4 or BB5 pump type.

 

Conclusions

Vespel® CR-6100 can help you avoid pump seizure during extreme events like running dry. The temperature limit is 500 F (260 C), allowing it to survive infernal heat waves. The material is not affected by electromagnetic pulses. polar shifts, or solar flares. As an added bonus, Vespel® CR-6100 has an indefinite shelf life, making it an ideal material to stockpile in your underground bunker, and the material is likely to hold its value in the case of hyperinflation.

 

In reality, you don’t have to stockpile the material. Boulden carries a huge inventory of stock sizes in the USA, Europe, and Singapore. You can generally receive whatever material you need in a matter of days.

 

To prepare your pump for whatever the future holds, please contact Boulden with your application details and dimensions. We’ll be happy to walk you through the installation details–assuming we have not been wiped out by an asteroid strike.

Todays Photo

All this talk of disaster is making me hungry. This is some excellent Bun Cha in Vietnam.

 

 

Helpful Links:

Standard Stock Sizes of Vespel® CR-6100

Vespel® CR-6100 Product Data Sheet

Vespel® CR-6100 Machining Guide

3MW Boiler Feed Pump Case Study

If you need any material or have any questions. Please contact us today. Until next time.

Contact Us Today To Learn More About Vespel and Boulden Company!

 

 

Upgrade to DuPont™ Vespel® CR-6100: 100%

Upgrading pumps with composite wear componentsThere is great satisfaction in doing a job all the way.

100%

In South Africa, when you make a statement that someone agrees with, they say “100 %”–similar to how other English speakers say “absolutely.” With that in mind, we want the pumps upgraded to Vespel® CR-6100 to be upgraded 100% whenever possible.

 

Review

 

When you upgrade your pumps to Vespel® CR-6100, there are two steps:

  • Eliminate the metal-to-metal contact points in the pump
  • Reduce the running clearance (of wear rings, center bushings, and throttle bushings)

Upgrading your pumps to Vespel CR-6100 Step #1

Our recommendation when upgrading to Vespel® CR-6100 is to convert all of the stationary wear parts to Vespel® CR-6100. All of the rotating parts remain metal, thus eliminating all of the metal-to-metal contact points in the pump. This essentially eliminates the risk of pump seizure.

 

Yet, once in a while, customers try to make a small change instead of fully upgrading the pump. The three partial upgrades we run into are:

Overhung Pumps

Older pumps with long slender shafts (high L/D ratios) create problems for mechanical seals due to excessive shaft deflection. If you want to increase the rotor stability of these pumps using the wear parts, you will want to upgrade the wear rings to Vespel® CR-6100 and reduce the clearance.

 

The reason is that the Lomakin Effect-the hydraulic force which stabilizes the rotor-is driven by differential pressure and the surface speed at the differential pressure interface. Wear rings have significant differential pressure and high velocity, creating a lot of stability from the Lomakin Effect. Throat bushings? Not so much.

 

Horizontal Multi-Stage Pumps

If a horizontal multi-stage pump like a boiler feed water pump seizes, it will usually occur at the center bushing or throttle bushing, depending on the pump type. These two components generally have the tightest clearance in the pump and will be the first points of contact. In these services, there is a temptation to only upgrade the one or two components which seized.

 

While this approach has been successful in reducing pump seizures, there are some limitations. Metal-to-metal contact points remain and thus there is still a possibility of seizure. If all of the wear parts are upgraded, the risk of seizure is essentially eliminated. Furthermore, the wear rings also add to the rotor stability and efficiency of these pumps. Upgrading the wear rings as well as the center and throttle bushings will make for a much better pump. Especially if you use the Boulden PERF-Seal™ design (patent-pending).

Two-stage kerosene pump with all the components upgrade to Vespel® CR-6100 and the PERF-Seal™ design

 

 

Center Bushing of a 2-stage pump.

 

Vertically Suspended Pumps

Vespel® CR-6100 is a great material for vertically suspended pump shaft bearings in LPG, butane, natural gas liquids (NGL), and other flashing products. It can survive running dry at start up with limited wear. It doesn’t break like a carbon part. This application for Vespel® CR-6100 is so common that Boulden carries a huge inventory of standard stock sizes for the dimensions typically used for shaft bearings.

 

What some users miss is the opportunity to also upgrade the case rings of these pumps and reduce the clearance. This addition to the upgrade eliminates the other potential seizing points in the pump. Furthermore, reducing the clearance increase the pump efficiency and reduces the NPSHR–all of this making the pump easier to operate.

 

In Summary

The only partial upgrade above which we do not recommend is trying to stabilize a rotor with a throat bushing. In our experience, this approach is marginally successful at best. The other partial upgrades have worked and there are situations where they are necessary. But, given the choice, why not do the job 100%?

 

The main point is to recognize that the maximum improvement in reliability, safety, and efficiency will be achieved if you upgrade all of the wear parts (Table 1) in your pump to Vespel® CR-6100.

Table 1: Components to upgrade to Vespel® CR-6100

Overhung Pumps Between Bearings Pumps Vertically Suspended Pumps
Case Wear Rings Case Wear Rings Case Wear Rings
Throat Bushings Throat Bushings Throat Bushings
Inter-Stage Bushings Line-shaft bearings  
Center-Stage Bushings Bowl bearings  
Throttle Bushings Bottom bushings

Contact Boulden Today for your Vespel® CR-6100 Needs!

If you have a pump operating at less than 500 F (260 C) where you want to improve the reliability or efficiency, contact Boulden today. We can provide you all of the details required for your upgrade and have the Vespel® CR-6100 material required for the upgrade in stock in a wide range of sizes available for immediate delivery.

 

Helpful Links:

Standard Stock Sizes of Vespel® CR-6100

Boulden Installation Guide for Vespel® CR-6100

Vespel® CR-6100 Product Data Sheet

Vespel® CR-6100 Machining Guide

3MW Boiler Feed Pump Case Study

 

Stay Connected

Useful Links for using DuPont™ Vespel® CR-6100

Upgrading pumps with composite wear componentsTools to help you improve your pump operability, reliability, and efficiency

20 Years of  Vespel® CR-6100

Our favorite material recently passed a milestone. The first pump ever fitted with Vespel® CR-6100 was upgraded 20 years ago in November 1997.

 

The first pump was a vertically suspended condensate pump at a refinery in California. The pump was notorious for running dry, and it had failed once or twice per year for as long as the maintenance records went back. An engineer at the refinery “found” Vespel® CR-6100 and decided to put it to the test on the condensate pump. The pump survived repeated episodes of running dry and subsequently ran for many years without failure.

 

Since then, over 10,000 pumps across the globe have been upgraded with Vespel® CR-6100.

 

Useful Links For DuPont™ Vespel® CR-6100

When you are using Vespel® CR-6100 in your shop, or if you are recommending your favorite repair shop to perform the upgrade for you, the following links should prove helpful:

Standard Stock Sizes of Vespel® CR-6100

Boulden Installation Guide for Vespel® CR-6100

Vespel® CR-6100 Product Data Sheet

Vespel® CR-6100 Machining Guide

3MW Boiler Feed Pump Case Study

If you need any material or have any questions. Please contact us today. Until next time, be safe, and enjoy the holidays with your friends and family

Todays Photo

Proboscis Monkeys, Borneo

Proboscis Monkeys, Borneo

Contact Us Today To Learn More About Vespel and Boulden Company!

Contact Us Today To Learn More About Vespel and Boulden Company

 

 

 

 

 

 

infbytg

Upgrading Pumps With Composite Wear Components Part: 3

boulden1

Part 3: Reduce Clearance–Improve Pump Efficiency

Welcome to Part 3 in our series on upgrading pumps with composite wear parts.

In the first part of this series, we discussed how upgrading your pumps with composite wear parts can help avoid galling and seizing. Because composite parts do not gall or seize like metal parts, this allows you to reduce the clearance at these components in your pump.

In Part 2, we discussed how reducing the clearance at the wear rings, throttle bushings, and center-stage bushings creates a stabilizing force in your pump called The Lomakin Effect. This force helps to reduce vibration and shaft deflection, leading to longer seal and bearing life in your pumps.

Today, we will discuss how reducing the clearance in your pump also improves pump efficiency.

Background

According to a major centrifugal pump OEM, energy consumption accounts for 44% of the life cycle cost of a centrifugal pump. You can reduce this cost by upgrading the wear components to a composite material like Vespel® CR-6100 and reducing the clearance in your pump.

The specific components where you want to reduce the clearance are the pump wear rings, inter-stage rings, center-stage bushing, and throttle bushing. These components form the barriers between high-pressure and low-pressure areas within the pump. The differential pressure across these components creates internal recirculation within the pump, resulting in a loss of pump efficiency (Figure 1).

 

Leakage wear rings

Leakage past the wear rings (QL) creates efficiency loss

 

 

 

 

 

 

Which Pumps Produce the Biggest Gains?
When you upgrade these components to Vespel® CR-6100, you can typically reduce the clearance by 50% compared to the API minimum for metal parts. If you reduce the clearance by 50%, you reduce the internal recirculation by approximately 50%, leading to a significant efficiency gain.

If we consider only efficiency gains, horizontal multi-stage pumps usually offer the best return on investment from an upgrade to Vespel® CR-6100 with reduced clearance. These pumps have multiple leak paths across wear rings, inter-stage rings, center bushings, and throttle bushings. Because they have many stages, these pumps also tend to consume a lot of power. Consider the following cases where process plants have reduced the operating costs of their multi-stage horizontal pumps:

  • A power station upgraded a 3MW boiler feed water pump with Vespel® CR-6100 along with the Boulden PERF-Seal™ design and reduced clearance and recorded a 7% efficiency gain compared to a newly rebuilt pump with original clearances.
  • A refinery upgraded their hydrocracker charge pumps with Vespel® CR-6100 along with the Boulden PERF-Seal™ design and reduced clearance and recorded 4% more through put to their hydrocracker-a hugely profitable upgrade.
  • A product pipeline company upgraded their LPG shipping pumps with Vespel® CR-6100 and reduced clearance, resulting in a 4% efficiency gain.

Another area to consider is process pumps which are marginally undersized, requiring parallel pump operation to achieve 100% of the target process rate. Sometimes, a modification as simple as reducing the wear ring clearance can get you back to one-pump operation with a full-capacity spare pump.

The PERF-Seal™

To further increase the efficiency gain associated with reduced clearance, the components can be modified with the Boulden PERF-Seal™ design. Internal testing has shown that the PERF-Seal™ creates an additional reduction in flow across throttle bushings, center-stage bushings, and wear rings beyond what can be achieved with reduced clearance alone.

Conclusion

When you eliminate the metal-to-metal contact surfaces in your pumps and use Vespel® CR-6100 stationary wear components, you can then reduce the clearance. This reduction in clearance improves pump efficiency and lowers the operating cost of the pump. Numerous field examples exist where customers have saved tens of thousands of dollars on their annual pump operating costs with this simple upgrade.

If you have a pump where improved efficiency will save you money, contact Boulden today. We have a huge inventory of Vespel® CR-6100 standard sizes in stock ready for immediate shipment almost anywhere in the world.

For application and installation details, download the Boulden Installation Guide for Vespel® CR-6100

Camps Bay Beach in Cape Town, South Africa

Camps Bay Beach in Cape Town, South Africa

 

Boulden Company

Boulden Company

Boulden Company

Conshohocken, PA, USA

1-610-825-1515

Boulden International, S.ar.L

Ellange, Luxembourg

+352 26 39 33 99