Tag Archives: Vespel CR-6100

Case Study: DuPont™ Vespel® CR-6100 in 3MW Boiler Feed Water Pump with PERF-Seal™ design.

Better operability, reliability, and efficiency

The PERF-Seal™

A while back, we introduced the PERF-Seal™ design for center bushings, throttle bushings, and pump wear rings.

 

Below you can see the center bushing and case wear rings of a 2-stage pump which was upgraded to Vespel® CR-6100 with the PERF-Seal™ design

Center Bushing of a 2-stage pump.

Center Bushing of a 2-stage pump.

2-stage pump upgraded to Vespel® CR-6100 with the PERF-Seal™ design.

2-stage pump upgraded to Vespel® CR-6100 with the PERF-Seal™ design.

The holes drilled in the PERF-Seal™ create a turbulence field, thereby reducing leakage across the component–acting in a way similar to a labyrinth. However, unlike a labyrinth design, the PERF-Seal™maintains the same hydraulic stiffness as a plain wear ring and discourages tangential whirl of the process fluid.

 

Boulden worked with Mechanical Solutions to create an FEA model of the design and to create a custom test rig to validate the performance of the design. If you are interested in the results of this testing, Contact Boulden and we will be happy to share with you.

 

Boiler Feed Pump Case Study

 

We were approached by a power plant looking to upgrade their 3MW boiler feed pumps. Their process had changed over the years to require frequent cycling and they wanted to use Vespel® CR-6100 to avoid pump seizure. Due to the size of the pumps, increased efficiency was an added bonus.

 

We applied the PERF-Seal™ design to all of the stationary wear components–case rings, throttle bushing, and center bushing. The pump had demonstrated the following

  • No issues stopping and starting the pump during plant cycles
  • 10% lower power consumption during full load operation
  • Motors no longer run in the safety factor during full load operation

The pumps have now been running for 2 years. A full case study was recently published in POWER Magazine and is available here.

 

Until Next Time

 

Contact us if you have a boiler feed water pump you would like to upgrade.

If you need material, we have a huge inventory of standard stock sizes available for immediate shipment.

For details on how to install Vespel® CR-6100 into nearly any pump type, download the Boulden Installation Guide.

Today’s Photo

Skull Island, Trang An, Vietnam

Skull Island, Trang An, Vietnam

Contact Us Today To Learn More About Vespel and Boulden Company!

Contact Us Today To Learn More About Vespel and Boulden Company!

 

 

 

 

 

 

gytinfb

Upgrading Pumps With Composite Wear Components Part: 9

Upgrading pumps with composite wear componentsPart 9: Vertically Suspended Pumps with Separate Discharge (API Type VS4)

Review

Last week, we looked at vertically suspended pumps with the discharge through the column. This week, we take a look at vertically suspended pumps with a separate discharge (API Type VS4).

Vertically suspended pumps with separate discharge are generally used for sump pumps or wastewater pumps. It seems that these pumps cause headaches at most plants. The shaft bushings wear out leading to chronic repairs. Over the years, Vespel® CR-6100 has been used in a lot of these pumps, sometimes the pump life has been extended from a few months to several years; sometimes the pump life has not improved. Therefore, it is important to identify the failure mode before making the upgrade. We have used our experience to create the roadmap below.

Define the Service

The first step is to clarify “sump pump” or “waste water pump”, which are generic terms encompassing a wide range of services. Some services are pumping primarily chemicals mixed with water, and some of them are pumping primarily water mixed with dirt. Some of the sumps are so dirty, that the pump suction strainer seems to be immersed in mud. Another variable is that the shaft bearings are flushed with different arrangements. Some of them are flushed with the process fluid, others with clean water, and others are greased.

Given the range of service conditions, there are several different problems which can cause the shaft bearings to fail. However, there are some commonalities. First, by design, the shaft bearings are along the column of the pump with a separate discharge for the process fluid. The bearings can run dry at start-up until the flushing fluid arrives. Sometimes, the external water flush is turned off; sometimes the flush lines from the process fluid are plugged; sometimes the grease supply runs out. In a chemical sump, the mix of chemicals can cause corrosion with metal wear parts. Finally, in very dirty sumps where the bearings are flushed with the process fluid, abrasive wear tends to be the main problem.

The Road Map

Considering the above, we have created the following table to guide your selection of where to use Vespel® CR-6100 in sump pump services:

Vespel CR-6100 sump pump services.

Vespel CR-6100 sump pump services.

*Some of the alternatives to consider are switching to a clean water flush or looking at an abrasive resistant, non-seizing combination for the shaft bushings and sleeve. This generally entails a hardened sleeve and an abrasive resistant bushing material. If you have any doubts about whether Vespel® CR-6100 is a good fit for your service, contact Boulden to discuss.

Vertical Pump Conclusion

To finish our discussion of vertically suspended pumps, we will talk about assembly and installation issues which impact pump reliability. Until then, use the above information as a guide on how to use Vespel® CR-6100 in your pumps with a separate discharge. If you need any material, contact Boulden. We have whatever size and quantity you need in stock and ready for immediate delivery.

For information on how to install Vespel® CR-6100 into nearly any centrifugal pump type, download the Boulden Installation Guide.

Contact Us Today To Learn More About Vespel and Boulden Company!

Contact Us Today To Learn More About Vespel and Boulden Company!

fbintw

ytg

Today’s Photo

Late Night Snack, Thailand

Late Night Snack, Thailand

 

 

 

 

 

 

 

Boulden Company

Conshohocken, PA, USA

1-610-825-1515

 

Boulden International, S.ar.L

Ellange, Luxembourg

+352 26 39 33 99

Upgrading Pumps With Composite Wear Components Part: 7

Upgrading pumps with composite wear componentsPart 7: Between Bearings, Radially Split Pumps (API Types BB2, BB4, and BB5)

Review

DuPont™ Vespel® CR-6100 is a composite material which is used for the stationary wear parts of your pump and can be used in nearly all process chemicals from cryogenic temperatures to 500 F (260 C).

The upgrade to Vespel® CR-6100 wear parts involves two steps: eliminate the metal-to-metal contact points in the pump to minimize the risk of pump seizure, then reduce clearance to improve reliability and increase efficiency.

Radially Split Pumps

Today, we cover the details on using Vespel® CR-6100 to upgrade your between-bearings, radially-split pumps. The components we want to upgrade in these pumps are the case rings, throttle bushing, and throat bushings.

Single and two-stage BB2 style pumps are widely used in refining and petrochemical applications featuring higher temperatures and low NPSH available. Upgrading the wear rings (and inter-stage bushing in two-stage designs) with Vespel® CR-6100 and reduced clearance will help maintain rotor stability, improve efficiency, and reduce the pump NPSHR.

Multi-stage BB4 and BB5 designs are used in several ideal applications for Vespel® CR-6100: unit charge pumps in refinery, petrochemical, and gas processing along with boiler feed water in many different industries. Upgrading the wear rings and throttle bushings of these pumps with Vespel® CR-6100 and reducing the clearance can produce significant efficiency gains of 4-6%. Higher efficiency translates to either lower operating cost as your pump uses less energy to produce the same flow, or increased throughput which can pay for the upgrade in a matter of days

Wear Rings

The key point in upgrading the wear rings in these designs is to ensure the Vespel® CR-6100 is retained against differential pressure. In many designs, the original case wear rings are manufactured with an “L” shaped profile as shown in Figure 1. This shape of this design will, in most cases, retain the rings against differential pressure. You only need to modify the original design to incorporate the press fit required for Vespel® CR-6100 and then final machine the rings after they are pressed into the diffusers.

Vespel® CR-6100 case rings for a hydrocracker charge pump

Vespel® CR-6100 case rings for a hydrocracker charge pump

 

In some pumps, however, the case rings go straight across the diffusers. When they are metal rings, they are usually welded in place. To replace these designs with Vespel® CR-6100, you may need to modify the diffusers to incorporate an “L” shaped profile, or design another method of retaining the components against differential pressure. If you have any questions, contact Boulden with the pump cross sectional drawing and we can help.

Throttle Bushings (aka Balance Drums)

The throttle bushings of BB4 and BB5 pump types can be exposed to high differential pressures. For these components, Boulden has developed a patent-pending design called the PERF-Seal™ which improves the performance and dramatically increases the differential pressure capability of composite materials used in this position.

Boulden recommends the PERF-Seal™ design for all throttle bushings in BB4 and BB5 pumps. Contact us and we can either supply machined parts or provide drawings for you to manufacture the components in your shop for the upgrade.

To be continued…

Our final look at specific pump types will feature vertically suspended pumps. After that, we will cover a few specific topics and wrap up this series.

Until then, if you have a radially split pump where you would like to improve the reliability or efficiency, contact Boulden today. We can provide you all of the details required for your upgrade and have the Vespel® CR-6100 in stock in a wide range of sizes available for immediate delivery.
For details on installing Vespel® CR-6100 into nearly any centrifugal pump type, download the Boulden Installation Guide.

Contact Us Today To Learn More About Vespel and Boulden Company!

Contact Us Today To Learn More About Vespel and Boulden Company!

Upgrading Pumps With Composite Wear Components Part: 5

Upgrading pumps with composite wear componentsPart 5: Upgrading overhung pump types with DuPont™ Vespel® CR-6100.

Review

So far, we have discussed how upgrading your pumps with composite wear parts can help avoid galling and seizing, which allows you to reduce the clearance in your pump. This small change increases the Lomakin Effect and makes your pump more reliable. Reduced clearance also improves pump efficiency, leading to a lower pump life cycle cost.

Last month, we highlighted that Vespel® CR-6100 is installed in compression in the stationary parts of your pump–wear rings, throttle bushings, throat bushings, and vertical pump shaft bearings–and can be used in nearly all process chemicals from cryogenic temperatures to 500 F (260 C).

Today, we start discussing how to install Vespel® CR-6100 to upgrade your overhung pumps, which typically make up the majority of the centrifugal pump population in a process plant. For most designs, there are only three parts to upgrade to Vespel® CR-6100: two case wear rings and the throat bushing.

Manufacturer Case Wear Rings from Vespel® CR-6100

You can usually manufacture the case rings from solid Vespel® CR-6100 and press them directly into the case and head of the pump. Because the pump casing can often be quite large and difficult to handle, it is generally easiest to design the case rings such that they do not require final machining. The way to do this is to assume there is a 1:1 ratio between the press fit and the closure of the inside diameter during the press fit.

For example, if your case rings require 0.020″ (0.50 mm) press fit, machine the inside diameter 0.020″ larger than the final target dimension before the press fit. After the ring is pressed into place, the inside diameter will decrease by 0.020″ and will match the target dimension (give or take a small tolerance).

Alternatively, you can use a metal ring as a “holder”. First, press the Vespel® CR-6100 into the metal ring and then final machine the Vespel® CR-6100 to the desired clearance. This is sometimes a better choice for case rings with very large radial walls or rings with “L” shaped profiles (See Photo 1). By using an insert you can use standard stock sizes of Vespel® CR-6100.

case rings with Vespel CR-6100

Photo 1: Insert into “L” profile case ring

Vespel® CR-6100 can be used for the Throat Bushings

Several mechanical seal flush plans require a close clearance throat bushing to increase the seal chamber pressure, to isolate cooled seal flush fluid from hot process fluid, or to isolate clean seal flush fluid from dirty or corrosive process fluid. Vespel® CR-6100 can be used for the throat bushing.

To set the clearance of the throat bushing, consult your mechanical seal supplier. They should recommend a clearance based on your seal flush plan such that your seal operates with the correct pressure and flow rate of seal flush.

Which Pumps

Reducing the clearance at the wear rings will improve the efficiency of all of your overhung pumps. That said, some pumps can be considered with higher priority than others.

The first place to look is older pumps with long slender shafts with high L/D ratios (see Photo 2), especially two-stage overhung pumps. These pumps were typically built for packing and have been converted to mechanical seals. These designs often excessive shaft deflection, making it difficult for seals to meet current reliability and emissions standards. Closing the wear ring clearance will add stability to the rotor and provide the seals a better operating environment. On the two-stage overhung pumps, you can also upgrade the bushing between the stages for additional support.

Overhung pump

Photo 2: Overhung pump with high L/D ratio

Next, look at your largest overhung pumps. These pumps will typically have higher radial loads when running away from their design point and potentially experience more shaft deflection. Plus, they will consume the most power, generally offering the best payout for efficiency gains.

Finally, consider upgrading your OH4-vertical inline, rigidly coupled pumps. Because these pumps have no bearing housing, they rely upon the motor bearing and the wear rings for radial stability. Reducing the wear ring clearance can often improve the reliability of these pumps.

Upgrading Pumps to be continued…

In the next months, we will discuss upgrading horizontal between bearings pumps and vertically suspended pumps.

Until then, if you have an overhung pump where you would like to improve the reliability or efficiency, contact Boulden today. We can provide you all of the details required for your upgrade and have the Vespel® CR-6100 material required for the upgrade in stock is a wide range of sizes available for immediate delivery.

header.png

To Learn More About Vespel CR-6100 Click here!

Upgrading Pumps With Composite Wear Components Part: 3

boulden1

Part 3: Reduce Clearance–Improve Pump Efficiency

Welcome to Part 3 in our series on upgrading pumps with composite wear parts.

In the first part of this series, we discussed how upgrading your pumps with composite wear parts can help avoid galling and seizing. Because composite parts do not gall or seize like metal parts, this allows you to reduce the clearance at these components in your pump.

In Part 2, we discussed how reducing the clearance at the wear rings, throttle bushings, and center-stage bushings creates a stabilizing force in your pump called The Lomakin Effect. This force helps to reduce vibration and shaft deflection, leading to longer seal and bearing life in your pumps.

Today, we will discuss how reducing the clearance in your pump also improves pump efficiency.

Background

According to a major centrifugal pump OEM, energy consumption accounts for 44% of the life cycle cost of a centrifugal pump. You can reduce this cost by upgrading the wear components to a composite material like Vespel® CR-6100 and reducing the clearance in your pump.

The specific components where you want to reduce the clearance are the pump wear rings, inter-stage rings, center-stage bushing, and throttle bushing. These components form the barriers between high-pressure and low-pressure areas within the pump. The differential pressure across these components creates internal recirculation within the pump, resulting in a loss of pump efficiency (Figure 1).

 

Leakage wear rings

Leakage past the wear rings (QL) creates efficiency loss

 

 

 

 

 

 

Which Pumps Produce the Biggest Gains?
When you upgrade these components to Vespel® CR-6100, you can typically reduce the clearance by 50% compared to the API minimum for metal parts. If you reduce the clearance by 50%, you reduce the internal recirculation by approximately 50%, leading to a significant efficiency gain.

If we consider only efficiency gains, horizontal multi-stage pumps usually offer the best return on investment from an upgrade to Vespel® CR-6100 with reduced clearance. These pumps have multiple leak paths across wear rings, inter-stage rings, center bushings, and throttle bushings. Because they have many stages, these pumps also tend to consume a lot of power. Consider the following cases where process plants have reduced the operating costs of their multi-stage horizontal pumps:

  • A power station upgraded a 3MW boiler feed water pump with Vespel® CR-6100 along with the Boulden PERF-Seal™ design and reduced clearance and recorded a 7% efficiency gain compared to a newly rebuilt pump with original clearances.
  • A refinery upgraded their hydrocracker charge pumps with Vespel® CR-6100 along with the Boulden PERF-Seal™ design and reduced clearance and recorded 4% more through put to their hydrocracker-a hugely profitable upgrade.
  • A product pipeline company upgraded their LPG shipping pumps with Vespel® CR-6100 and reduced clearance, resulting in a 4% efficiency gain.

Another area to consider is process pumps which are marginally undersized, requiring parallel pump operation to achieve 100% of the target process rate. Sometimes, a modification as simple as reducing the wear ring clearance can get you back to one-pump operation with a full-capacity spare pump.

The PERF-Seal™

To further increase the efficiency gain associated with reduced clearance, the components can be modified with the Boulden PERF-Seal™ design. Internal testing has shown that the PERF-Seal™ creates an additional reduction in flow across throttle bushings, center-stage bushings, and wear rings beyond what can be achieved with reduced clearance alone.

Conclusion

When you eliminate the metal-to-metal contact surfaces in your pumps and use Vespel® CR-6100 stationary wear components, you can then reduce the clearance. This reduction in clearance improves pump efficiency and lowers the operating cost of the pump. Numerous field examples exist where customers have saved tens of thousands of dollars on their annual pump operating costs with this simple upgrade.

If you have a pump where improved efficiency will save you money, contact Boulden today. We have a huge inventory of Vespel® CR-6100 standard sizes in stock ready for immediate shipment almost anywhere in the world.

For application and installation details, download the Boulden Installation Guide for Vespel® CR-6100

Camps Bay Beach in Cape Town, South Africa

Camps Bay Beach in Cape Town, South Africa

 

Boulden Company

Boulden Company

Boulden Company

Conshohocken, PA, USA

1-610-825-1515

Boulden International, S.ar.L

Ellange, Luxembourg

+352 26 39 33 99