Tag Archives: Vespel Rules

Prepping Your Metal Parts

Prepare your pump parts for an upgrade to DuPont™ Vespel CR-6100

Review on Pump Parts and upgrading to Vespel CR-6100

The National Geographic Channel used to run a show called Doomsday Preppers where survivalist families would prepare for apocalyptic disasters and societal collapse. Although that sounds like a lot of fun, at Boulden, we are more concerned with helping your pumps survive adverse process conditions with an upgrade to DuPont™ Vespel® CR-6100.

 

Last month, we outlined the measurements required for a Vespel® CR-6100 installation. When you have decided to go forward with the upgrade, the first step will be to prepare the metal parts to facilitate the installation.

 

Start with a Little Chamfer

Vespel® CR-6100 is used for stationary wear components–throttle bushings, case wear rings, center-stage bushings, inter-stage case rings, vertical pump shaft bearings, throat bushings, agitator bearings, API separator bearings-basically any product lubricated wear part.

 

The material is installed with a significant press fit. To facilitate the press fit operation, the metal bore into which you will be pressing the Vespel® CR-6100 requires a small chamfer or radius (Figure 1). It is very important that any corners or sharp edges are fully broken and smoothed with a stone so that the metal edge does not remove material from the outside surface of the Vespel® CR-6100 during the press operation.

Figure 1: Chamfer or Radius Leading Edge to facilitate press fit. (Note shoulder on low-pressure side.)

 

 

 

 

 

 

 

 

 

Make Sure There is a “Shoulder” or “Step”

For any part exposed to differential pressure, it is important that the design features a shoulder or step at the low-pressure end (shown on the right side of Figure 1) to ensure the differential pressure does not dislodge the Vespel® CR-6100 during operation.

 

Some radially split multi-stage pumps (BB4 and BB5) pumps feature metal wear rings welded into the pump diffusers with no step or shoulder incorporated in the design. In this case, you can consider modifying the diffusers so that the case wear rings have an “L” shaped profile like the rings below which were used in a hydrocracker charge pump.

Figure 2: “L” Shaped wear ring profile for BB4 or BB5 pump type.

 

Conclusions

Vespel® CR-6100 can help you avoid pump seizure during extreme events like running dry. The temperature limit is 500 F (260 C), allowing it to survive infernal heat waves. The material is not affected by electromagnetic pulses. polar shifts, or solar flares. As an added bonus, Vespel® CR-6100 has an indefinite shelf life, making it an ideal material to stockpile in your underground bunker, and the material is likely to hold its value in the case of hyperinflation.

 

In reality, you don’t have to stockpile the material. Boulden carries a huge inventory of stock sizes in the USA, Europe, and Singapore. You can generally receive whatever material you need in a matter of days.

 

To prepare your pump for whatever the future holds, please contact Boulden with your application details and dimensions. We’ll be happy to walk you through the installation details–assuming we have not been wiped out by an asteroid strike.

Todays Photo

All this talk of disaster is making me hungry. This is some excellent Bun Cha in Vietnam.

 

 

Helpful Links:

Standard Stock Sizes of Vespel® CR-6100

Vespel® CR-6100 Product Data Sheet

Vespel® CR-6100 Machining Guide

3MW Boiler Feed Pump Case Study

If you need any material or have any questions. Please contact us today. Until next time.

Contact Us Today To Learn More About Vespel and Boulden Company!

 

 

Useful Links for using DuPont™ Vespel® CR-6100

Upgrading pumps with composite wear componentsTools to help you improve your pump operability, reliability, and efficiency

20 Years of  Vespel® CR-6100

Our favorite material recently passed a milestone. The first pump ever fitted with Vespel® CR-6100 was upgraded 20 years ago in November 1997.

 

The first pump was a vertically suspended condensate pump at a refinery in California. The pump was notorious for running dry, and it had failed once or twice per year for as long as the maintenance records went back. An engineer at the refinery “found” Vespel® CR-6100 and decided to put it to the test on the condensate pump. The pump survived repeated episodes of running dry and subsequently ran for many years without failure.

 

Since then, over 10,000 pumps across the globe have been upgraded with Vespel® CR-6100.

 

Useful Links For DuPont™ Vespel® CR-6100

When you are using Vespel® CR-6100 in your shop, or if you are recommending your favorite repair shop to perform the upgrade for you, the following links should prove helpful:

Standard Stock Sizes of Vespel® CR-6100

Boulden Installation Guide for Vespel® CR-6100

Vespel® CR-6100 Product Data Sheet

Vespel® CR-6100 Machining Guide

3MW Boiler Feed Pump Case Study

If you need any material or have any questions. Please contact us today. Until next time, be safe, and enjoy the holidays with your friends and family

Todays Photo

Proboscis Monkeys, Borneo

Proboscis Monkeys, Borneo

Contact Us Today To Learn More About Vespel and Boulden Company!

Contact Us Today To Learn More About Vespel and Boulden Company

 

 

 

 

 

 

infbytg

7 Rules for Using Vespel® CR-6100

Upgrading pumps with composite wear componentsWe just completed our series on upgrading pumps with DuPont™ Vespel® CR-6100, getting into details on how to upgrade various horizontal and vertical pump types. We discussed reducing the clearance of the wear rings, upgrading throttle bushings with the PERF-Seal design, and upgrading vertically suspended pump shaft bearings.

Today, let’s try to condense it all down into a short list of guidelines which we can apply to just about any pump. Follow these rules and we can ensure we are using Vespel® CR-6100 properly and improving our pump reliability.

7 Rules for Using DuPont™ Vespel® CR-6100 

  • Stay under the temperature limit of 500 F (260 C)
  • Only stationary parts, mounted in compression
  • Shoulder on the low pressure side to retain the part against differential pressure
  • Avoid extremely abrasive services such as slurries, bottoms, or slops
  • Press fit, clearance, and axial length of part from the Boulden Installation Guide
  • Pump rotor must turn freely when the pump is assembled and ready for commissioning
  • Use PERF-Seal™ design for throttle and center bushings of multi-stage pumps

What do you think?

Did we miss anything? Contact us to let us know your ideas.

Until next time, if you have an application you would like to discuss, contact Boulden.

Need Vespel CR-6100 or other materials?

If you need material, we have a huge inventory of standard stock sizes available for immediate shipment.

For details on how to install Vespel® CR-6100 into nearly any pump type, download the Boulden Installation Guide.

Todays Photo

Borobodur, Indonesia

The Borobudur temple. The largest buddhist temple, and most visited site in Indonesia

 

Contact Us Today To Learn More About Vespel and Boulden Company!

Contact Us Today To Learn More About Vespel and Boulden Company!

 

 

 

 

 

 

gytinfb